Showing results: 151 - 165 of 707 items found.
-
CB52 -
CAMI Research Inc. (CableEye®)
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade. To ensure that 4-wire resistance measurements remain accurate, CAMI recommends running the verification check every quarter. A 4-wire measurement module that is out of calibration will give inaccurate results. Some (maybe all) resistance measurements will be incorrect. Consequently, it may Pass what should Fail and, conversely, Fail what should Pass. In other words product yield will be contaminated due to unreliable measurements.
-
CX-D12 -
Shenzhen Chuangxin Instruments Co., Ltd.
It’s strictly designed according to IEC60695-11-2, IEC60332-1, GB/T18380.11-2008, GB/T18380.12-2008 etc. Stainless steel screen with a sliding burner handle support for approaching or movingback the flame from the sample under test according to the CEI standards for test on cables.
-
72-9170 -
Tenma
Quickly identify wires and tests continuityFits in any pocket or tool kit Invaluable in all audio, video, network, telecom and electrical installations
-
PHCT55 -
Pyle Audio Inc.
The PHCT55 is a two-piece item that tests telephone wire continuity. Play a test tone on one end and listen on the other, judge continuity, and diagnose break points.
-
CB29H -
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination. Each contains four 16-pole screw terminal blocks that will accept bare wires from 12- to 30-gauge in size. The metal jaws firmly grip an inserted wire without damaging or distorting the end, and the space between each terminal block may be used as a wire channel to guide wires neatly to the side. For each channel, a pair of holes is provided through which wire ties may be inserted to hold the wire bundles in place.
-
LANTESTPRO -
StarTech.com USA LLP
The StarTech.com Advanced RJ45 LAN Cable tester allows a single person to test several long cables faster and more efficiently than ever before. The tester uses remote loop-back plugs that each have their own unique ID number that the tester can identify.
-
CAMI Research Inc. (CableEye®)
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
CB51 -
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models. The CB51, sold without connectors, contains four sets of 60 solder pads accommodating numerous configurations of surface mount and TH connectors aligned or staggered pins at 1.25mmm and 1.5mm pitch. There are four preset locations for automatic detection & display of any-pin-count connector up to 60-pins. Yet, any single set may be fitted with any combination of lower pin count connectors that total to 60 or less (e.g. a 40-pin with a 10-pin). Connectors soldered in non-preset positions will also appear graphically correct once they are mapped with PinMap (optional software).
-
MT-8000 series -
Guangzhou Wanglu Communications Co., Ltd.
● 8 inch retina touch screen, 2048*1536 resolution● 8MP TVI CVI AHD camera test● 3G-SDI, HD-SDI /EX-SDI 2.0 camera test (Optional)● 4K H.265 IP camera test, DH and Hik test tool for brand camera testing● TVI 5.0 support audio test● 1310/1550 Dual wavelength, max test range 150KM ● Automatic analysis of various linkers/fusion points, easy analyze of various events● Save and view the testing curves, support zoom and move curves, view details● Support saving cures number ≥30000pcs● Support UCC menu control mode A-TYPE, B-TYPE select● 4K 60FPS HDMI input & 4K 30 FPS HDMI output
-
PinMap™ -
CAMI Research Inc. (CableEye®)
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
72-9205 -
Tenma
Quickly test VGA / UL2919 cables No need to carry bulky, expensive cable testers to test only one or two cable types Mini cable tester fits easily in your pocket or tool box, and requires no external power Confirms conductor continuity with sequential LED's Save time and money by diagnosing connectivity issues All units are powered by a cross compatible 3xAA battery pack or USB cable (both included) Most units measure 2" x 2" x 1" or less!
-
72-9245 -
Tenma
The 72-9245 is a Mini Cable Tester for SATA/ESATA cable. Mini cable tester fits easily in your pocket or tool box.
-
72-9225 -
Tenma
The 72-9225 is a Mini Cable Tester for HDMI 1.4 cable. Mini cable tester fits easily in your pocket or tool box.
-
72-9210 -
Tenma
The 72-9210 is a Mini Cable Tester for USB 3.0 (A/B, A/A, A/micro B) cable. Mini cable tester fits easily in your pocket or tool box.
-
72-9200 -
Tenma
The 72-9200 is a Mini Cable Tester with USB Power Cable and Battery. Quickly test DB-9/RS-232 cables. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini cable tester fits easily in your pocket or tool box and requires no external power. Confirms conductor continuity with sequential LED's. Save time and money by diagnosing connectivity issues.